Steel - structured buildings are widely used due to their numerous advantages. However, to ensure their long - term safe use and maintain good performance, daily maintenance is of great importance. The following are some practical tips.
Structural Part
(I) Appearance Inspection
Regular Patrol InspectionConduct a comprehensive appearance inspection at least once a quarter. Observe whether there is any deformation, abrasion, or paint peeling on the surface of the steel structure. Pay special attention to the beam - column joints, as these parts are under complex stress and are prone to problems. For example, if there is a local depression on the surface of a steel beam, it may indicate that the structure has been subjected to abnormal external forces, and further inspection is required.
Key - focus AreasFocus on areas prone to water accumulation and dust accumulation, such as roof gutters and the areas around parapet walls. Water accumulation may accelerate the corrosion of steel, and dust accumulation may cover up surface defects of the steel. If rust spots appear in the gutter, clean it in a timely manner and carry out anti - rust treatment.
(II) Anti - corrosion Maintenance
Coating RepairIf the anti - corrosion coating on the surface of the steel structure shows signs of peeling or flaking, repair it in a timely manner. First, use sandpaper or a grinder to roughen the damaged area and its surroundings, clean it thoroughly, and then repaint according to the original coating system. In the case of large - area coating aging and failure, re - coating is required. Pay attention to selecting a paint that matches the original coating to ensure adhesion and anti - corrosion performance.
Regular Anti - corrosion TreatmentConduct a comprehensive anti - corrosion inspection and assessment every 3 - 5 years according to the environment where the steel structure is located. In high - humidity and high - corrosion environments, such as coastal areas or chemical industrial parks, the cycle should be appropriately shortened, and it can be carried out every 2 - 3 years. If necessary, long - term anti - corrosion measures such as hot - dip galvanizing and spraying zinc - aluminum coatings can be adopted.
(III) Inspection of Connection Components
Bolt TighteningRegularly inspect the bolt - connected parts to check whether the bolts are loose or missing. Spot - check the bolts with a wrench. If looseness is found, tighten them in a timely manner. For bolts in important structural parts, such as the connection bolts of crane beams, use a torque wrench to tighten them according to the specified torque value.
Welded Joint InspectionConduct an appearance inspection of the welded joints every six months to check whether there are defects such as cracks, pores, and slag inclusions in the welds. After finding problems, mark them in a timely manner and entrust professionals to carry out non - destructive testing (such as ultrasonic testing and magnetic particle testing) to determine the degree of defects. For minor defects, grinding and repair can be carried out; for serious defects, re - welding is required, and the welding process should comply with relevant standards.
Enclosure System
(I) Roof Maintenance
Drainage System CleaningClean the roof drainage gutters and downpipes every month to remove debris, leaves, etc., and ensure smooth drainage. Check the drainage system in a timely manner after a heavy rain. If drainage is found to be 不畅,unclog it immediately. Long - term water accumulation will increase the roof load, resulting in roof deformation and even leakage.
Roof Panel InspectionRegularly check whether the roof color - coated steel plates or sandwich panels are damaged or scratched. For small - area damage, use special sealants and repair materials for repair; for large - area damage, replace the plates. When replacing, pay attention to ensuring that the type and specifications of the plates are consistent with the original ones, and ensure firm connection and good sealing.
(II) Wall Maintenance
Wall Flatness InspectionObserve whether the wall is flat and whether there are bulges or deformations. If the wall is found to be uneven, it may be caused by internal structural problems of the wall or uneven external forces, and the cause needs to be further investigated. For minor bulges, local reinforcement treatment can be adopted; for serious deformations, demolition and reinstallation are required.
Sealing Inspection around Doors and WindowsCheck whether the sealing rubber strips around the doors and windows on the wall are aging or falling off, and whether the sealant is cracked. If such situations occur, replace the rubber strips and re - apply the sealant in a timely manner to ensure good sealing around the doors and windows, preventing rainwater leakage and air penetration.
Other Aspects
(I) Maintenance of Fire - prevention Facilities
Fire - proof Coating InspectionInspect the fire - proof coating on the surface of the steel structure every year to check whether the coating thickness meets the requirements and whether there is any peeling or cracking. For parts that do not meet the requirements, repair or re - apply the fire - proof coating in a timely manner to ensure the fire - resistance performance of the steel structure.
Fire - fighting Equipment InspectionRegularly check whether fire - fighting facilities such as fire hydrants and fire extinguishers are in good condition and effective. Ensure that the fire - fighting passage is unobstructed and no debris is piled up.
(II) Electrical System Inspection
Inspection of Wires and CablesInspect the electrical lines every six months to check whether the wires and cables are damaged or aging, and whether the joints are loose. If problems are found, replace or repair them in a timely manner to prevent fires caused by electrical failures.
Grounding System TestingTest the grounding system every year to ensure that the grounding resistance meets the requirements. Good grounding can effectively prevent lightning strikes and electrical accidents, and ensure the safety of personnel and equipment.
By following these daily maintenance tips, problems in steel - structured buildings can be detected and solved in a timely manner, extending their service life and ensuring the safe and stable operation of the buildings.


